jungle/doc/install.md

# Installing NixOS in a new node

This article shows the steps to install NixOS in a node following the
configuration of the repo.

## Prepare the disk

Create a main partition and label it `nixos` following [the manual][1].

[1]: https://nixos.org/manual/nixos/stable/index.html#sec-installation-manual-partitioning.

```
# disk=/dev/sdX
# parted $disk -- mklabel msdos
# parted $disk -- mkpart primary 1MB -8GB
# parted $disk -- mkpart primary linux-swap -8GB 100%
# parted $disk -- set 1 boot on
```

Then create an etx4 filesystem, labeled `nixos` where the system will be
installed. **Ensure that no other partition has the same label.**

```
# mkfs.ext4 -L nixos "${disk}1"
# mkswap -L swap "${disk}2"
# mount ${disk}1 /mnt
# lsblk -f $disk
NAME   FSTYPE LABEL UUID                                 MOUNTPOINT
sdX
`-sdX1 ext4   nixos 10d73b75-809c-4fa3-b99d-4fab2f0d0d8e /mnt
```

## Prepare nix and nixos-install

Mount the nix store from the xeon07 node in read-only /nix.

```
# mkdir /nix
# mount -o ro xeon07:/nix /nix
```

Get the nix binary and nixos-install tool from xeon07:

```
# ssh xeon07 'readlink -f $(which nix)'
/nix/store/0sxbaj71c4c4n43qhdxm31f56gjalksw-nix-2.13.3/bin/nix
# ssh xeon07 'readlink -f $(which nixos-install)'
/nix/store/9yq8ps06ysr2pfiwiij39ny56yk3pdcs-nixos-install/bin/nixos-install
```

And add them to the PATH:

```
# export PATH=$PATH:/nix/store/0sxbaj71c4c4n43qhdxm31f56gjalksw-nix-2.13.3/bin
# export PATH=$PATH:/nix/store/9yq8ps06ysr2pfiwiij39ny56yk3pdcs-nixos-install/bin/
# nix --version
nix (Nix) 2.13.3
```

## Adapt owl configuration

Clone owl repo:

```
$ git clone git@bscpm03.bsc.es:rarias/owl.git
$ cd owl
```

Edit the configuration to your needs.

## Install from another Linux OS

Install nixOS into the storage drive.

```
# nixos-install --flake --root /mnt .#xeon0X
```

At this point, the nixOS grub has been installed into the nixos device, which
is not the default boot device. To keep both the old Linux and NixOS grubs, add
an entry into the old Linux grub to jump into the new grub.

```
# echo "

menuentry 'NixOS' {
    insmod chain
    search --no-floppy --label nixos --set root
    configfile /boot/grub/grub.cfg
} " >> /etc/grub.d/40_custom
```

Rebuild grub config.

```
# grub2-mkconfig -o /boot/grub/grub.cfg
```

To boot into NixOS manually, reboot and select NixOS in the grub menu to boot
into NixOS.

To temporarily boot into NixOS only on the next reboot run:

```
# grub2-reboot 'NixOS'
```

To permanently boot into NixOS as the default boot OS, edit `/etc/default/grub/`:

```
GRUB_DEFAULT='NixOS'
```

And update grub.

```
# grub2-mkconfig -o /boot/grub/grub.cfg
```

## Build the nixos kexec image

```
# nix build .#nixosConfigurations.xeon02.config.system.build.kexecTree -v
```