jungle/doc/install.md

177 lines
4.0 KiB
Markdown
Raw Normal View History

2023-04-27 16:36:48 +02:00
# Installing NixOS in a new node
This article shows the steps to install NixOS in a node following the
configuration of the repo.
2023-08-24 12:29:44 +02:00
## Enable the serial console
By default, the nodes have the serial console disabled in the GRUB and also boot
without the serial enabled.
To enable the serial console in the GRUB, set in /etc/default/grub the following
lines:
```
GRUB_TERMINAL="console serial"
GRUB_SERIAL_COMMAND="serial --speed=115200 --unit=0 --word=8 --parity=no --stop=1"
```
To boot Linux with the serial enabled, so you can see the boot log and login via
serial set:
```
GRUB_CMDLINE_LINUX="console=ttyS0,115200n8 console=tty0"
```
Then update the grub config:
```
# grub2-mkconfig -o /boot/grub2/grub.cfg
```
And reboot.
2023-04-27 16:36:48 +02:00
## Prepare the disk
Create a main partition and label it `nixos` following [the manual][1].
[1]: https://nixos.org/manual/nixos/stable/index.html#sec-installation-manual-partitioning.
```
# disk=/dev/sdX
# parted $disk -- mklabel msdos
2023-05-10 10:58:27 +02:00
# parted $disk -- mkpart primary 1MB -8GB
# parted $disk -- mkpart primary linux-swap -8GB 100%
2023-04-27 16:36:48 +02:00
# parted $disk -- set 1 boot on
```
Then create an etx4 filesystem, labeled `nixos` where the system will be
installed. **Ensure that no other partition has the same label.**
```
# mkfs.ext4 -L nixos "${disk}1"
2023-05-10 10:58:27 +02:00
# mkswap -L swap "${disk}2"
2023-04-27 16:36:48 +02:00
# mount ${disk}1 /mnt
# lsblk -f $disk
NAME FSTYPE LABEL UUID MOUNTPOINT
sdX
`-sdX1 ext4 nixos 10d73b75-809c-4fa3-b99d-4fab2f0d0d8e /mnt
```
## Prepare nix and nixos-install
2023-06-14 11:15:00 +02:00
Mount the nix store from the hut node in read-only /nix.
2023-04-27 16:36:48 +02:00
```
# mkdir /nix
2023-06-14 11:15:00 +02:00
# mount -o ro hut:/nix /nix
2023-04-27 16:36:48 +02:00
```
2023-06-14 11:15:00 +02:00
Get the nix binary and nixos-install tool from hut:
2023-04-27 16:36:48 +02:00
```
2023-06-14 11:15:00 +02:00
# ssh hut 'readlink -f $(which nix)'
2023-04-27 16:36:48 +02:00
/nix/store/0sxbaj71c4c4n43qhdxm31f56gjalksw-nix-2.13.3/bin/nix
2023-06-14 11:15:00 +02:00
# ssh hut 'readlink -f $(which nixos-install)'
2023-04-27 16:36:48 +02:00
/nix/store/9yq8ps06ysr2pfiwiij39ny56yk3pdcs-nixos-install/bin/nixos-install
```
And add them to the PATH:
```
# export PATH=$PATH:/nix/store/0sxbaj71c4c4n43qhdxm31f56gjalksw-nix-2.13.3/bin
# export PATH=$PATH:/nix/store/9yq8ps06ysr2pfiwiij39ny56yk3pdcs-nixos-install/bin/
# nix --version
nix (Nix) 2.13.3
```
2023-05-10 10:58:27 +02:00
## Adapt owl configuration
Clone owl repo:
```
$ git clone git@bscpm03.bsc.es:rarias/owl.git
$ cd owl
```
Edit the configuration to your needs.
## Install from another Linux OS
Install nixOS into the storage drive.
```
# nixos-install --flake --root /mnt .#xeon0X
```
At this point, the nixOS grub has been installed into the nixos device, which
is not the default boot device. To keep both the old Linux and NixOS grubs, add
an entry into the old Linux grub to jump into the new grub.
```
# echo "
menuentry 'NixOS' {
insmod chain
search --no-floppy --label nixos --set root
configfile /boot/grub/grub.cfg
} " >> /etc/grub.d/40_custom
```
Rebuild grub config.
```
# grub2-mkconfig -o /boot/grub/grub.cfg
```
To boot into NixOS manually, reboot and select NixOS in the grub menu to boot
into NixOS.
To temporarily boot into NixOS only on the next reboot run:
```
# grub2-reboot 'NixOS'
```
To permanently boot into NixOS as the default boot OS, edit `/etc/default/grub/`:
```
GRUB_DEFAULT='NixOS'
```
And update grub.
```
# grub2-mkconfig -o /boot/grub/grub.cfg
```
2023-04-27 16:36:48 +02:00
## Build the nixos kexec image
```
# nix build .#nixosConfigurations.xeon02.config.system.build.kexecTree -v
```
## Chain NixOS in same disk with other systems
To install NixOS on a partition along another system which controls the GRUB,
first disable the grub device, so the GRUB is not installed in the disk by
NixOS (only the /boot files will be generated):
```
boot.loader.grub.device = "nodev";
```
Then add the following entry to the old GRUB configuration:
```
menuentry 'NixOS' {
insmod chain
search --no-floppy --label nixos --set root
configfile /boot/grub/grub.cfg
}
```
The partition with NixOS must have the label "nixos" for it to be found. New
system configuration entries will be stored in the GRUB configuration managed
by NixOS, so there is no need to change the old GRUB settings.